Click your remote to view step-by-step instructions on how to program the remote for your TV
Champion
To program your remote control, please do the following:
- Turn on the device (DVD, AUDIO, TV)
- Press the device button (DVD, AUDIO, TV)
- Press and hold the Setup button at the top right comer of the remote until the device button blinks twice.
- Press the device button again (DVD,AUDIO, TV), the button should remain lit.
- Press and hold down the OK/SELECT button
- Let go of the OK/SELECT button when the device turns off
You have now programmed your remote to control your device.
NOTE: The remote control comes pre-programmed for your digital receiver.
BACK TO TOP
Pulse
Quick Reference Guide
To program your remote control, please do the following:
- Turn on your TV
- Press the device button (TV)
- Press and hold the Setup button until the light below the power button blinks twice.
- Press and hold down the OK/ENTER button
- When the TV turns off, let go of the OK/ENTER button
You have now programmed your remote to control your device.
NOTE: The remote control comes pre-programmed for your digital receiver.
BACK TO TOP
Maestro
To program your remote control, please do the following:
- Turn on the device (TV or AUDIO)
- Press and hold the MENU and OK buttons until the Power Button flashes, then release both buttons.
- Enter 9 9 1
- Press 1 to search for a TV Code or 3 to search for a Audio Device Code. The power button should again flash twice after the 1 or the 3.
- While aiming the remote at the device press and release the Cursor Up button repeatedly until the device turns off.
- Press OK to lock in the code when the device turns off. The power button will again flash twice.
You have now programmed your remote to control your device.
NOTE: The remote control comes pre-programmed for your digital receiver.
BACK TO TOP
Maestro - Netflix
Quick Reference Guide
To program your remote control, please do the following:
You have now programmed your remote to control your device.
NOTE: The remote control comes pre-programmed for your digital receiver.
BACK TO TOP
Atlas 1056
To program your remote control, please do the following:
- Turn on the device (VCR, DVD, Home Theatre, etc.)
- Press the device button (VCR, DVD, AUX (Home Theatre or other device), TV, CBL)
- Press and hold the Setup button at the top left comer of the remote until the device button blinks twice.
- Press 9-9-1 (The button should blink twice)
- Press Power
- Point the remote at the device and press CH+ repeatedly until the device turns off
- Press the Setup button when the device turns off
You have now programmed your remote to control your device.
NOTE: The remote control comes pre-programmed for your digital receiver.
BACK TO TOP
DRC 800
To program this remote for your TV:
- Press and hold a device button (AUDIO, DVD/VCR, or TV) until each device button lights up and the button for the device you selected remains lit.
- Press the Power button. The device button will blink three times.
- Press the UP ARROW button (above the OK button). The remote will attempt to turn the power on/off for the device you selected.
- If the device turned on or off, press OK. The remote is now programmed for that device.
- If the device did not turn on or off, repeat step three until it does, then press OK.
NOTE: The remote control comes pre-programmed for your digital receiver.
BACK TO TOP
Contour
(available only in Sunshine Coast, BC and surrounding areas)
To program this remote for your TV:
- Turn the TV on.
- Press the TV button on the remote.
- Press and hold the SETUP button until the TV button blinks twice.
- Enter 9 9 9 1. The TV button will blink twice.
- Aim the remote at the TV and press MUTE. The remote will now send codes from its library to the TV.
- When your TV turns off, press SETUP once. Your remote is now programmed for your TV.
- If the TV does not respond, press CH+ and the remote will test the next TV code. Continue to press CH+ until the TV turns off. Then press SETUP once to finish.
NOTE: The remote control comes pre-programmed for your digital receiver.
BACK TO TOP
DSR-470 (HITS-QT)
To program this remote for your TV:
- Turn on your TV.
- Press the TV button on your remote until the button blinks.
- While pointing the remote control at your TV, press the up arrow button to scan to the next code.
- If the remote tries a code that is correct for your TV, your TV will turn off.
- If your TV does not turn off, keep pressing the up arrow button repeatedly until your TV turns off.
- When your TV turns off, indicating the remote has found the correct code, press the Enter button. The TV button will flash rapidly several times and turn off.
NOTE: The remote control comes pre-programmed for your digital receiver.
BACK TO TOP
DRC 400
- Turn on your TV
- On the remote, press and hold TV until you see each of the device buttons blink in sequence.
- Once the TV button stays lit continuously, press the up arrow button (above the OK button) once to start search mode.
- Press POWER once. The TV button will blink.
- If your television does not turn off, press the up arrow button and then POWER again. Repeat until your TV turns off.
- When your television turns off, press OK and the TV button will blink three times. Your remote is now programmed for your TV.
NOTE: The remote control comes pre-programmed for your digital receiver.
BACK TO TOP
UR5
- Turn on your TV.
- On your remote, press the TV button and the OK button simultaneiously until the TV button lights up.
- NOTE: The button will stay lit 20 seconds. The next step must be completed during this time.
- Press the CH+ button. The remote will send a series of power off commands to your TV. When your TV turns off, release the CH+ button.
- Press the TV button to finish. It will blink twice to confirm. Your remote is now programmed for your TV.
NOTE: The remote control comes pre-programmed for your digital receiver.
BACK TO TOP